Hydro Power Generation Maintenance & Repair
Hydropower is one of the oldest sources of renewable energy, with many of the turbines running today installed in the early 1900s and are still in service. When a unit goes down, the cost of an unplanned outage climbs fast. The Chalmers & Kubeck Hydro Division keeps aging and modern hydro equipment running with field disassembly and installation, unit maintenance, shop repair, and full Kaplan and Francis rehabilitation, backed by the machining and fabrication capabilities C&K has built since 1950.
Hydro Field Services
We service Kaplan turbines in horizontal, vertical, bulb, pit, S, and tube configurations, along with Francis turbines, Pelton turbines, and pump units. Our field services include:
- Full unit disassembly and reassembly
- Inspections, including NDE/NDT, runout testing, and Kaplan runner internals
- Preventive maintenance and general troubleshooting
- Rotor pole removal and reinstallation
- Seal replacement and alignment services
- New equipment installation and facility upgrades
- Safety audits
- Subcontractor management
- Nationwide crew mobilization
Our team can also reverse engineer components to update existing prints or create new ones, and we provide project management and craft labor support for projects of any size.
Shop Repair and Hydro Machining
Our machining department repairs most rotating hydro components in-house.
- Shafts: Coupling faces, turbine and generator shafts, and intermediate shafts, up to 30 feet in length and 100,000 lbs
- Francis runners: Bucket repairs, cavitation repair, band and crown turning, and weld repairs, up to 32 feet in diameter
- Kaplan runners: Blade stem and periphery machining, trunnion sealing surface machining, and full refurbishment, up to 32 feet in diameter
- Headcovers and bottom rings: Buildup and machining, bushing work, and cavitation repair, up to 32 feet in diameter
- Wicket gates: Sealing surfaces, sleeve installation, replacement, and turning
- Line boring and fabrication: Shaft coupling faces, hub trunnion bushings, pins, discharge rings, draft tubes, and sealing rings
C&K also services the valves, actuators, pumps, and gearboxes that support a hydro unit. You can review that full scope on our power industries page.
Maintenance, Parts, and Training
We support hydro plants on an ongoing basis with annual and weekly operations support, blasting and painting, oil pressure testing, and preventive maintenance programs built around your schedule. Our supplier relationships let us source bushings, blade seals, labyrinth seals, and shaft sleeves when you need them. We also offer facility upgrade planning, basic hydro training, and consulting to help your team build internal knowledge.
Recent Hydro Projects

HS2
C&K disassembled, inspected, and reassembled the discharge ring, seal, and oil pipe assembly on this Kaplan turbine-generator unit. The crew replaced the Kaplan oil pipes and seals, rebuilt the oil head, repaired a wicket gate arm, and supported the customer through commissioning.
- Location: Dumas, Arkansas
- Customer: Arkansas Electric Cooperative Corporation
- Completed: November 2025

Pawtucket Unit 1
C&K overhauled the turbine and generator on this 45-degree vertical Kaplan unit, following an overhaul on the sister unit the year before. The runner, shafting, bearing housings, linkage, and packing box were refurbished in our shop, and the unit was recommissioned at peak rated output.
- Location: Pawtucket, Rhode Island
- Customer: Relevate Power
- Completed: March 2026

Pelton
C&K refurbished this 32 MW vertical Francis unit, including partial disassembly and reassembly and removal and reinstallation of the rotor poles. The crew also installed an owner-supplied high-pressure lift system and built a temporary shelter to protect the generator rotor.
- Location: Madras, Oregon
- Customer: Portland General Electric Company
- Completed: October 2023

Great Falls Unit 2
C&K performed a full rehabilitation on one of three vertical Kaplan tube turbines on the Passaic River. The runner, shaft, and discharge ring were refurbished in our shop and reassembled on site, along with equipment modifications the owner requested.
- Location: Paterson, New Jersey
- Customer: Eagle Creek Renewable Energy
- Completed: September 2024
Talk to a Hydropower Specialist
Our Hydro Division team brings more than seven decades of combined industry experience and works a two-shift schedule so we can respond quickly when you call. Tell us what your plant needs, and we will put the right people, equipment, and certifications on it. Contact C&K to start a conversation with our hydro team.

Frequently Asked Questions
Our Hydro team has worked on equipment from 16 turbine manufacturers. We service Kaplan turbines in horizontal, vertical, bulb, pit, S, and tube configurations, along with Francis turbines, Pelton turbines, and pump units.
We build the eroded metal back up with weld repair, then re-machine the surface to its original profile. Our shop handles cavitation repair on Francis runners, headcovers, and bottom rings up to 32 feet in diameter. Restoring the profile brings efficiency back and extends the runner’s service life between overhauls.
Yes. Our crews refurbish the turbine while also handling generator work like rotor pole removal and reinstallation. Running both under one provider keeps the outage schedule tighter and gives you a single documented record.
C&K sources common parts like bushings, seals, and shaft sleeves through trusted supplier relationships. When a part is no longer available, we reverse engineer it from the existing hardware or measurements and manufacture a new one to specification.
